Orion-system VCM-X/RNE Controller Manuale Utente Pagina 80
- Pagina / 92
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
APPENDIX A - SAVE, LOAD, COPY SETPOINTS
VCM-X / RNE Operator Interface SD
80
Modular Service Tool Instructions
From any menu screen, press <BALANCE-TEST>. The Unit Selection
Screen will appear requesting that you enter the unit ID number.
Unit Selection
Enter Unit ID#
Selected ID#: XXXX
*00*
Enter the network unit ID for the controller you want to save the setpoints
from. Example, ‘102’ for Loop 1 / Unit 2. Then press <ENTER>. You
must type in the number, even if it is “1”. Once communication is es-
tablished, the *00* at the bottom will disappear. After a brief pause,
press
<> to get to the Balance - Test Screen shown below.
Outputs Force
Para Blocks
Save/Copy/Restore
Scroll down to the ‘Save/Copy/Restore’ option and press <ENTER>.
This will take you to the Save Setpoints screen.
System Manager SD Instructions
From any Main screen, press <SETPOINTS>. The screen below will
appear because this option requires passcode clearance. Only a Level 2
passcode can change setpoints.
THIS ACTION REQUIRES
PASSCODE CLEARANCE
Enter Passcode: XXXX
If the correct passcode was entered, the Unit Selection Screen will be
displayed.
Unit Selection*00*
Enter Unit ID#
Selected ID#: XXXX
Enter the Unit ID of the controller you wish to change schedules for
and press <ENTER>. You must type in the number, even if it is “1”.
Once communication is established, the *00* at the top will disappear.
Then
press <>.
NOTE: If the *00* remains, it indicates a communication
failure to the controller.
The following screen will be displayed:
Change Setpoints
Configure Unit
Save/Copy/Restore
Scroll down to the ‘Save/Copy/Restore’ option and press <ENTER>.
This will take you to the Save Setpoints screen.
Save Setpoints - Network Mode
From the Save Setpoints Screen shown below:
Save Setpoints
Press Enter To Save
Press <ENTER> and a setpoint fi le will be saved to the SD card. You
will receive a message that the save was successful. This fi le is specifi c
to this controller on this loop.
Saving Setpoints
- VCM-X / RNE Controller 1
- Operator Interface SD 1
- Technical Guide 1
- SD CARD UPDATING INSTRUCTIONS 2
- IMPORTANT NOTICE 2
- SYSTEM CONNECTION 4
- Modular Service Tool SD 4
- Modular System Manager SD 6
- Back View 7
- Power/Comm Board Wiring 8
- Stand Alone Connection 9
- MODULAR SERVICE TOOL SD 10
- Modular Service Tool Keys 10
- Setup Screens 11
- Programming the Time 11
- Programming the Date 11
- Alarm and Override Search 13
- Schedules and Holidays 14
- Holiday Start/Stop Times 15
- Schedule Override 15
- SYSTEM MANAGER SD 16
- Setting the Operating Mode 18
- Changing Passcodes 19
- Holiday Start/Stop Times 23
- VCM-X CONFIGURATION 24
- VCM-X CONFIGURATION 25
- VCM-X Confi guration Screens 25
- RNE CONFIGURATION 34
- RNE CONFIGURATION 35
- RNE Confi guration Screens 35
- VCM-X / RNE SETPOINTS 44
- VCM-X / RNE Setpoint Screens 45
- VCM-X / RNE STATUS 56
- VCM-X / RNE Status Screens 56
- > 65
- > to 65
- VAV Zone Confi guration 66
- <0> if you 67
- <0> 67
- Separate Loop 68
- VAV/Zone Setpoint Screens 69
- VAV/ZONE CONTROLLER STATUS 73
- VAV/Zone Status Screens 73
- VAV/ZONE CONTROLLER STATUS 74
- VAV/Zone Damper Force Modes 75
- MINILINK PD STATUS 76
- MINILINK PD PROGRAMMING 77
- TROUBLESHOOTING 78
- VCM-X / RNE Outputs Force 78
- Saving Setpoints 80
- SD Memory Card Update 82
- WattMaster Controllers 83
- E-BUS Modules 84
- Setpoints.........45 86
- VAV/Zone.........71 86
- Setpoint.........52 88
- VAV/Zone Status.........72 89
Prodotti e manuali riguardandi Hardware Orion-system VCM-X/RNE Controller
Hardware Orion-system VCM Manuale Utente
(52 pagine)
(52 pagine)
Hardware Orion-system PT-Link-LON Manuale Utente
(40 pagine)
(40 pagine)
Datalogic Scanning PDA uživatelské příručky
Začínající na S
Commenti su questo manuale