Orion-system VCM-X E-BUS Component Manuale Utente Pagina 6
- Pagina / 128
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Systems Overview
VCM-X Component & System Wiring
6
Overview
The Orion system components can be confi gured into several types
of systems. It is a good idea to become familiar with the different
types of systems and their architecture by reading the information in
this section and looking at the confi guration diagrams in the System
Confi gurations section of this manual. The information below is de-
signed to help you understand how the system components integrate
with each other and the available confi guration options.
System Types
Four different system confi gurations are available depending on
the type and number of controllers that you have on your system.
1. Stand Alone
(See Figure 3, page 22 for Connection Diagram)
2. Interconnected
(See Figure 4, page 23 for Connection Diagram)
3. Networked Single Loop
(See Figures 5-9, pages 24-28 for Connection
Diagrams)
4. Networked Multiple Loop
(See Figures 10-11, pages 29-30 for Connection
Diagrams)
5. Computer, CommLink 5, IP Module, USB-Link 2
(See Figures 54-58, pages 76-80 for Connection
Diagrams)
System Type Definitions
Stand Alone
This system consists of a single VCM-X E-BUS Controller. Pro-
gramming and status monitoring are accomplished by one or more
of the following methods.
1. By using an operator interface. This can be a Modular
System Manager, a System Manager TS II, a Modular
Service Tool, or all 3 devices.
2. A computer interface can also be used in conjunction
with the other operator interfaces listed above, or
by itself. This requires a CommLink 5 or USB-Link 2
and a personal computer with the Prism 2 computer
front end software installed.
Interconnected
This system consists of a group of VCM-X E-BUS Controllers
interconnected with communication cable to allow programming
from one central location. Broadcasting between controllers is not
available. Programming and status monitoring are accomplished by
one or more of the following methods.
1. By using an operator interface. This can be a Modular
System Manager, a System Manager TS II, a Modular
Service Tool, or all 3 devices.
2. A computer interface can also be used in conjunction
with the other operator interfaces listed above, or by
itself. This requires a CommLink 5 or USB-Link 2 and a
personal computer with the Prism 2 computer front end
software installed.
Networked Single Loop
The Networked Single Loop system, as its name implies, consists of
a single communications loop. This loop utilizes a network device to
share information that is broadcast from one controller to all control-
lers on the loop. The system can consist of the following devices.
1. A series of VCM-X E-BUS Controllers that utilizes
a network device to share information that is broadcast
from one controller to all controllers on the loop.
2. A single VCM-X E-BUS Controller and a series of VAV/
Zone Controllers. These VAV/Zone Controllers can
either be of the Modular type or Non-modular type.
The Modular type use Power/Comm Boards and
prefabricated cables and the Non-Modular type utilize
terminals and 2 conductor twisted pair with shield wire.
A network device is used to share information which is
broadcast back and forth between all controllers on the
loop.
These systems require a network device in the form of either a
CommLink 5 communications interface or a MiniLink Polling De-
vice. Both network devices may also be used together. Programming
and status monitoring are accomplished by the following methods:
1. By using an operator interface. This can be a Modular
System Manager, a System Manager TS II, a Modular
Service Tool, or all 3 devices.
2. A computer interface can also be used in conjunction
with the other operator interfaces listed above, or
by itself. This requires a CommLink 5 or USB-Link 2
and a personal computer with the Prism 2 computer
front end software installed.
When using the MiniLink Polling Device alone, only the System
Manager, System Manager TS II, and Modular Service Tool can be
used to program and monitor the system. With the addition of the
CommLink 5, the Prism 2 computer front end software and a PC
can be used to program and monitor the system in addition to the
Modular Service Tool, Modular System Manager, and the System
Manager TS II.
System Types
- VCM-X E-BUS Component & 1
- Table of Contents 2
- Commissioning 5
- Systems Overview 6
- System Types 6
- Wiring Considerations 8
- Wire & Transformer Sizing 9
- Orion VCM-X System 9
- WARNING! 10
- Stand-Alone 11
- System Installation 12
- Networked Single Loop 13
- Networked Multiple Loop 17
- System Commissioning 20
- Overview 20
- System Configurations 21
- Typical Stand Alone System 22
- Interconnected System 23
- Networked Single Loop System 24
- Note: CommLink Must Be Set 29
- For Multiple Loop Operation 29
- Connect To Modular 30
- I/O Connectors 30
- Located On Back 30
- Of The System Manager 30
- VCM-X E-BUS 31
- VCM-X E-BUS Controller Wiring 32
- Main Controller Wiring 32
- Main Controller Addressing 33
- Sensor Wiring 34
- Duct-Mounted CO 35
- VCM-X E-BUS Controller 37
- Caution: 39
- VCM-X Expansion 41
- Expansion Module Wiring 41
- VCM-X Expansion Module Wiring 42
- Input Wiring 42
- Output Wiring 43
- VCM-X Expansion Module 46
- OVCMX-BinInput-4BIN-1A.CDR 47
- OA Humidity Sensor 48
- Space Humidity Sensor 49
- RA Humidity Sensor 50
- OVCMX-BldgPr-Wr-1A.CDR 52
- Building Pressure Control 52
- Damper Actuator 52
- Modular Cable 53
- Connect To VCM-X Controller 53
- Connect To Next Expansion 53
- Board (When Used) 53
- Modulating Cooling Device 54
- (Configurable) 54
- Expansion 55
- OVCMX-12RelayWire-1A.CDR 56
- GTC116 Series, GreenTrol 57
- MicroTrans 57
- Modular & Non-Modular 59
- VAV/Zone Controller 59
- Diagrams 59
- OE210-02, OE211-02, OE212-02 60
- OE217-00 / OE217-01 60
- Digital Room Sensor 60
- Slaved Zone Wiring 68
- Communication Devices 69
- OE392-12 Modular System 71
- Manager SD 71
- Back of Front Cover 71
- OE392-10 75
- System Manager TS II 75
- Back View 75
- IP-ModInstall1A.CDR 77
- CommLink 5 79
- Communication Loop Wiring 81
- CAUTION! 83
- Add-On Devices Diagrams 85
- Add-On Devices 86
- GPC-X Controller Wiring 87
- GPC-XP Controller Wiring 89
- GPC-XP CommLink Setting 91
- OE332-23-GPC-XP 91
- GBD-X Controller - CO 92
- Applications Wiring 92
- Applications Wiring (Cont’d) 93
- Module Wiring 97
- & Connections 97
- OE370-23-HP1C 98
- One Condenser 98
- Head Pressure Module 98
- OE370-23-HP2C2 99
- Two Condenser 99
- Head Pressure II Module 99
- OE370-23-FD-A 100
- Full Digital Module 100
- OE370-23-DD-C 101
- Dual Digital Module 101
- Controller Wiring 102
- AAON MODGAS-X Wiring 103
- (OE377-26-00060) 104
- MODGAS-XWR CONTROLLER 104
- MHGRV-X CONTROLLER 107
- (OE377-26-00059) 107
- OE334-26-WSHP-X2 108
- Water Source 108
- Heat Pump X2 Module 108
- AAON PREHEAT-X Wiring 110
- AAON MODGAS II Wiring 111
- AAON MHGRV II Controller 112
- Only Required When More Than 113
- Valves Are Needed 113
- MHGRV III Controller 113
- Miscellaneous Diagrams 115
- & Technical Information 115
- Modular Room Sensor Wiring 116
- EPROM Chip Locations 117
- EPROM Chip Locations (Cont’d) 118
- SD Memory Card Update 121
- E-BUS Modules 122
- OE275-01 Suction Pressure 126
- Refrigerant 126
Prodotti e manuali riguardandi Hardware Orion-system VCM-X E-BUS Component
Hardware Orion-system MHGRV-X Manuale Utente
(26 pagine)
(26 pagine)
Hardware Orion-system MODGAS-XWR Manuale Utente
(28 pagine)
(28 pagine)
Hardware Orion-system MODGAS-X Manuale Utente
(28 pagine)
(28 pagine)
Hardware Orion-system PREHEAT-X Manuale Utente
(28 pagine)
(28 pagine)
Hardware Orion-system MHGRV II Manuale Utente
(12 pagine)
(12 pagine)
Hardware Orion-system MODGAS II Manuale Utente
(22 pagine)
(22 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale