Orion-system VCC-X Controller Manuale Utente Scaricare il pdf (Pagina 27)

VCC-X Operator Interface SD

VCC-X CONFIGURATION

VCC-X Conﬁ guration Screens

Conﬁ guration Screen #9 - HVAC Mode Set By

Remote Contact

VCC-X Cnfg ID #

HVAC Mode Set By

Remote Contact: NO

USE < or > TO CHANGE

This option allows separate 24 VAC wet contact closures on the

VCC-X to force the unit into Heating, Cooling, and Dehumidiﬁ ca-

tion modes. If this option is selected, it applies to all three modes,

and all three modes will only be initiated by these contact closures.

See the VCC-X Remote Contact Control section of the Sequence

of Operations in the VCC-X Controller Technical Guide for more

details. Default is NO.

Conﬁ guration Screen #10 - SAT Reset Source

VCC-X Cnfg ID #

SAT Reset Source

No Reset

USE < or > TO CHANGE

This conﬁ guration option is not available if Single Zone VAV was

selected as the HVAC source. The Supply Air Setpoint can be “au-

tomatically” adjusted based on a selected reset source. This screen

allows you to choose this source.

Default is No Reset. The available

selections are as follows:

 No Reset—No SAT Setpoint Reset will occur. The SAT

Setpoints remain ﬁ xed.

 Space Temperature—The SAT Setpoints will be

adjusted based on the Space Temperature.

 Outdoor Temperature—The SAT Setpoints will be

adjusted based on the Outdoor Air Temperature.

 Return Air Temperature—The SAT Setpoints will be

adjusted based on the Return Air Temperature.

 Fan VFD Signal—The SAT Setpoints will be adjusted

based on the VFD Signal. This is good for Adjusting the

Setpoints based on the building’s load by looking at the

VFD speed.

 Remote Voltage—The SAT Setpoints will be

adjusted based on the Remote Supply Air Temperature

Voltage Reset Signal.

If the HVAC Source was set Single Zone VAV in Conﬁ guration

Screen #8, then line 3 on this screen will read No SAT Rst Allowed

and the line 4 will be blank.

Conﬁ guration Screen #11 - Reset Rate Interval

VCC-X Cnfg ID #

Reset Interval

Rate...: 30 s

[1 - 255 Seconds]

If you selected a Reset Source in Conﬁ guration Screen #10, enter

a value in seconds between 1-255. This value determines how fast

the Supply Air Temperature Setpoint is adjusted as the Reset Source

changes. Default is 30 seconds.

Conﬁ guration Screen #12 - Space Sensor Type

VCC-X Cnfg ID #

Space Sensor Type

NONE

USE < or > TO CHANGE

If this unit has a Space Sensor installed, select Analog if it is a

wired Thermistor temperature sensor. Select E-bus Space/RH if it

is a combination communicating temperature and humidity sensor.

Select Receive Broadcast if the Space Sensor is attached to a sepa-

rate device that will broadcast the reading, e.g., GPC-XP Controller.

Select Remote Sensor if using a Sensor connected to a separate Unit

Controller on the same loop (sharing a sensor). You can select the

Unit Controller that will have the space sensor on Conﬁ guration

Screen #13. Default is NONE.

Conﬁ guration Screen #13 - Remote Space

Sensor Board Address

VCC-X Cnfg ID #

Remote Space Sensor

Board Address: 0

If using a Remote Space Sensor (must be chosen in Conﬁ guration

Screen #12), enter the address of the board it is located on. This Unit

Controller has to be on the same loop as the Controller that will be

sharing the sensor.

Conﬁ guration Screen #14 - Outdoor Sensor Type

VCC-X Cnfg ID #

Outdoor Sensor Type

NONE

USE < or > TO CHANGE

If this unit has an Outdoor Air Sensor installed, select Analog if it

is a wired Thermistor temperature sensor. Select E-bus OAT/RH

if it is a combination communicating temperature and humidity

sensor. Select Receive Broadcast if the Outdoor Sensor is attached

to a separate device that will broadcast the reading, e.g., GPC-XP

Controller. Default is NONE.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 95 96

Commenti su questo manuale

Nessun commento

Orion-system VCC-X Controller Manuale Utente Pagina 27

Commenti su questo manuale

Prodotti e manuali riguardandi Hardware Orion-system VCC-X Controller